#
✕ nick:jannau
#asahi-dev · 2022-03-23 06:32
jannaualyssa: the preallocated vram is already carved out. if we could tell the native mode from the dcp iboot we should just reserve a new fb if the old one is too small
#asahi-dev · 2022-03-22 22:23
jannauGlanzmann: on the mini vram can fit 5.5 million pixels, would be good for 3440x1600 or 3840x1433 at 32bpp
#asahi-dev · 2022-03-22 22:14
jannauyes, I think so too, otherwise you shouldn't have seen just 1/4 on the 4k tv
#asahi-dev · 2022-03-22 22:11
jannauthat's for studio, I haven't looked on the m1n1 under macos 12.3 yet
#asahi-dev · 2022-03-22 21:47
jannauallocated vram is just large enough for 1920x1137 at 32bpp
#asahi-dev · 2022-03-22 21:36
jannaudisplay works after mapping vram
#asahi-dev · 2022-03-22 21:27
jannaumaybe, why should it map the framebuffer for dcp/disp0 if it doesn't init the devices
#asahi-dev · 2022-03-22 21:19
jannaudisplay breakage is caused by iboot not mapping the framebuffer
#asahi-dev · 2022-03-22 21:02
jannauI'll queue the patch. I think it is correct but it might not be complete
#asahi-dev · 2022-03-22 21:00
jannaualyssa: looks like a good first step for s2idle. I wonder if macos also suspends dcp via rtkit
#asahi-dev · 2022-03-22 20:49
jannauit's probably pmgr. clock/power gates have a die id in the most significant nibble. there's just a single pmgr instance which looks identical to a single m1 max
#asahi-dev · 2022-03-22 20:12
jannauseems to be just missed ranges conversion
#asahi-dev · 2022-03-22 19:57
jannauCPU cores have the m1 max MIDR part numbers, revision 0x20
#asahi-dev · 2022-03-22 19:55
jannauusb phy init on the second die fails
#asahi-dev · 2022-03-22 19:46
jannauproxy over uart works including chainload
#asahi-dev · 2022-03-22 19:43
jannauit fails to find the framebuffer DVA, I have no proxy access yet since usb init fails
#asahi-dev · 2022-03-22 19:11
jannaudisplay init fails and then "assert(irq < 0x1000); // Will probably need updating for multi-die"
#asahi-dev · 2022-03-22 18:56
jannaumaz: second try was a success. I would have been surprised if it is not one of the outer ports on the backside
#asahi-dev · 2022-03-22 18:54
jannauinstaller works up to kmutil after removing the the obvious "not yet" comments
#asahi-dev · 2022-03-22 18:53
jannauno, just testing. I need the uart to see where where m1n1 dies on the first boot attempt
#asahi-dev · 2022-03-22 18:50
jannaumagic usb-c port is the one next to the ethernet port and reset still works
#asahi-dev · 2022-03-22 18:46
jannauGlanzmann: you mean my broken 3.6 kg heavy uart?
#asahi-dev · 2022-03-22 18:33
jannauand finished
#asahi-dev · 2022-03-22 18:32
jannaufans are noticeable running, still updating
#asahi-dev · 2022-03-22 18:21
jannauif not I want my money back
#asahi-dev · 2022-03-22 18:21
jannauI hope there's not much to fix. apple did claim ultrafusion is transparent to software so I assume Linux will just work ;)
#asahi-dev · 2022-03-22 18:13
jannauI could have skipped that but I see little sense in investigating a franken macos 12.2
#asahi-dev · 2022-03-22 18:11
jannausomething heavy arrived and it is installing 5.27GB of updates
#asahi-dev · 2022-03-21 19:21
jannauindeed, fixed. thanks
#asahi-dev · 2022-03-21 19:11
jannauhttp://www.jannau.net/dcp_mbp14_12.2.1.log this is from march 6th and macos 12.2.1
#asahi-dev · 2022-03-20 22:43
jannauthe alarm mirror list in /etc/pacman.d/mirrorlist not /etc/pacman.d/mirrorlist.asahi
#asahi-dev · 2022-03-20 21:52
jannaumarcan: the minimal image has sydney and japan as mirrors in /etc/pacman.d/mirrorlist
#asahi-dev · 2022-03-20 20:06
jannau"failed to reinitialize core" is gone when booting without usb device connected
#asahi-dev · 2022-03-20 20:03
jannauno noticeable delay for fullspeed device and an usb-3 hub with integrated nic
#asahi-dev · 2022-03-20 20:00
jannau4.8 seconds for an usb stick
#asahi-dev · 2022-03-20 19:59
jannauI'm asking because it's almost exactly 5 seconds
#asahi-dev · 2022-03-20 19:57
jannau"tunables and/or fuses not available" is gone, otherwise unchanged behavior. Is it expected that it takes 5 seconds before the device is attached?
#asahi-dev · 2022-03-20 19:45
jannauthis is with usb-pd/hw uart connected btw
#asahi-dev · 2022-03-20 19:42
jannausven: https://www.jannau.net/atc_phy_core_reinit_fail.txt
#asahi-dev · 2022-03-20 19:36
jannauTiming O_DIRECT cached reads: 1516 MB in 2.00 seconds = 758.25 MB/sec
#asahi-dev · 2022-03-20 19:34
jannau"new SuperSpeed Plus Gen 2x1" after replugging, boot still fails with "failed to reinitialize core"
#asahi-dev · 2022-03-20 19:29
jannauno, I forgot to merge the m1n1 change
#asahi-dev · 2022-03-20 19:26
jannaumac mini
#asahi-dev · 2022-03-20 19:26
jannaureplugging fixes it but the device is just detected as high speed device
#asahi-dev · 2022-03-20 19:25
jannausven: atc-WIP fails for me with 'dwc3 382280000.usb: failed to reinitialize core' when booted with usb device connected. both bare metal and HV
#asahi-dev · 2022-03-20 18:31
jannaualyssa: m1n1 should print https://paste.debian.net/1235047/
#asahi-dev · 2022-03-20 18:28
jannauI assumed you can login via ssh
#asahi-dev · 2022-03-20 18:24
jannaualyssa: you can check if the reserved mem regions are ing the dtb with 'dtc -I fs -O dts -o - /proc/device-tree | grep -A 50 reserved-memory'
#asahi-dev · 2022-03-20 18:19
jannaudev_info()
#asahi-dev · 2022-03-20 18:18
jannauI would have expected 'apple-dart 231304000.iommu: reserved region: IOVA [mem 0x013fc000-0x0bd07fff] PA [mem 0x9da4f0000-0x9e4dfbfff]', not sure which log level though

plus ›