#
#asahi-dev · 2025-03-11 22:28
fl0_idprobably, as it's wobby when on a flat surface
#asahi-dev · 2025-03-11 22:27
PaulFertserThe battery failing?
#asahi-dev · 2025-03-11 22:26
fl0_idOT but also annoying, the pinebook pro has an unfortunate case of spicy pillow
#asahi-dev · 2025-03-11 22:15
chaos_princessit only matters for serial console (not vusb), but you'd be using a second mac for that
#asahi-dev · 2025-03-11 22:15
PaulFertserOK. All three ports on PBP are capable of high speed.
#asahi-dev · 2025-03-11 22:14
chaos_princessshouldn't matter, i've almost always used a usb2 only cable
#asahi-dev · 2025-03-11 22:14
PaulFertserIs it expected to be a high speed device or super speed?
#asahi-dev · 2025-03-11 22:13
chaos_princessmy trick to ensure the connection is not flaky is to power it down fully, set m1n1 as default boot, and then turn the device on by connecting the usb cable
#asahi-dev · 2025-03-11 22:12
fl0_idok will try those things but probably tomorrow :)
#asahi-dev · 2025-03-11 22:11
PaulFertserfl0_id: you can test it with any other USB device to be sure, you'll see messages in dmesg right away even with that shitty pinebook pro.
#asahi-dev · 2025-03-11 22:11
fl0_idchaos_princess ah ok that about hotplug is good to know. from the docs it was not obvious to me that it needed to be connected before
#asahi-dev · 2025-03-11 22:10
chaos_princessand m1n1 does not support hotplug
#asahi-dev · 2025-03-11 22:10
PaulFertserDo you confirm m1n1 should be detected as High Speed?
#asahi-dev · 2025-03-11 22:10
fl0_idPaulFertser true, I just don't trust this pinebook pro as I don't use it regularly and it has wonky firmware etc too
#asahi-dev · 2025-03-11 22:10
chaos_princess(yes, i am serious)
#asahi-dev · 2025-03-11 22:10
chaos_princesstry flipping the c side of the cable
#asahi-dev · 2025-03-11 22:10
PaulFertserAlso you can use Type-C to Type-C cable if you expect mac to be a USB Device.
#asahi-dev · 2025-03-11 22:09
fl0_idPaulFertser mmh yeah, but m1n1 output suggest all 3 ports are found
#asahi-dev · 2025-03-11 22:09
PaulFertserMachine can't matter there.
#asahi-dev · 2025-03-11 22:09
PaulFertserNo output means neither D+ nor D- are pulled up, so no USB 2.0 communication can happen at all.
#asahi-dev · 2025-03-11 22:09
fl0_idmaybe I'll try a different host machine tomorrow. different cable could take 1-2 days (as most cables I have are probably power only)
#asahi-dev · 2025-03-11 22:08
PaulFertserfl0_id: probably only one of the ports on M3 is used that way, or probably it uses SuperSpeed? I suggest you check the commit that claims that it adds support for USB Device for that board you have there.
#asahi-dev · 2025-03-11 22:07
fl0_idlsusb also didn't show anything connected
#asahi-dev · 2025-03-11 22:07
fl0_idas far as I can tell
#asahi-dev · 2025-03-11 22:07
fl0_idI did. no output there
#asahi-dev · 2025-03-11 22:06
PaulFertserfl0_id: I suggest you check dmesg to see what exactly happens from kernel point of view
#asahi-dev · 2025-03-11 21:58
fl0_idhey. so i proxy mode, does the host need any specific requirements, or the cable? Based on the docs I just used a normal usb-c to a cable that says it supports data up to 480 mb/s. but at least on the pinebook pro, no tty device showed up. also tried different ports on both devices
#asahi-dev · 2025-03-11 11:24
fl0_idat least I can do that from a linux machine, that makes things easier
#asahi-dev · 2025-03-11 11:23
fl0_idchadmed ah ok that clarifies it. Somehow I thought there was a built-in one
#asahi-dev · 2025-03-11 11:13
chadmedthere is no builtin console, you have to access it from a host machine
#asahi-dev · 2025-03-11 11:13
chadmedfl0_id: proxy mode is what you want
#asahi-dev · 2025-03-11 10:47
fl0_idusb seems to be initialized
#asahi-dev · 2025-03-11 10:47
fl0_idoutput is here: https://www.pastery.net/xkvucj/ (ocr'd so some small mistakes could be there like the last dot)
#asahi-dev · 2025-03-11 10:45
fl0_idhey, so for dumping adt etc I installed m1n1 on m3 max and that boots, but goes to proxy mode. This was just compiling as described on https://asahilinux.org/docs/sw/m1n1-user-guide/ so it shouldn't be a release build right? Do I need to add any payload in particular to get console mode?
#asahi-dev · 2025-03-11 04:39
adityajannau: what I can do is that I can implement the T2 over your tree and send a pr to Asahi. Then these can be sent together. Are you fine with that?
#asahi-dev · 2025-03-11 04:38
adityajannau: I traced the hid reports for the USB composite device. One report id is for keyboard, one for trackpad, one is something related to touchpad digitizer and last was unknown. None had dimensions.
#asahi-dev · 2025-03-10 21:20
jannaure dimensions report. can you trace what macos does? does it maybe use a different report id?
#asahi-dev · 2025-03-10 21:14
jannauI can't send out quickly since spi-hid needs cleanup and I would also want to combine some of hector's and my changes to avaid changing the parts twice in the same series
#asahi-dev · 2025-03-10 21:11
jannauI can priotize it somewhat to make sure that that happens
#asahi-dev · 2025-03-10 21:10
jannauI can't send the our patches out quickly (within days) but I was planning on submitting spi-hid and hid devices patches aiming for 6.16
#asahi-dev · 2025-03-10 21:08
jannauaditya: I'm not ok with https://github.com/t2linux/linux-t2-patches/blob/mtp/4003-HID-magicmouse-Add-support-for-trackpads-found-on-T2.patch it does to much at once
#asahi-dev · 2025-03-10 20:24
adityasven: Sure, can jannau please confirm if he/she is ok with this. I would have to add his/her signed-off-by.
#asahi-dev · 2025-03-10 20:19
svenif most code is taken from some other tree you'll need to either send them as From: for the original author or add Co-developed-by tags fwiw
#asahi-dev · 2025-03-10 20:18
adityaSo I've hardcoded the values like others.
#asahi-dev · 2025-03-10 20:18
adityaAlso, I've noticed getting the hardware dimensions is possible using a report id on Apple Silicon for these trackpads. Unfortunately, that doesn't seem to work with T2.
#asahi-dev · 2025-03-10 20:17
adityaLink: https://github.com/t2linux/linux-t2-patches/tree/mtp
#asahi-dev · 2025-03-10 20:17
adityaI just wanted to tell that we have finally managed to add support for T2 macs using the hid Magic Mouse driver. The 400x patches here apply cleanly on the upstream tree. Since they will clash with the Asahi Linux tree, and most code is taken from there, in case Asahi wants to take them up, kindly inform me. Else I plan to upstream them soon.
#asahi-dev · 2025-03-10 20:11
adityaHi
#asahi-dev · 2025-03-10 19:42
svenlol
#asahi-dev · 2025-03-10 19:29
funderscore🤣

plus ›