#
✕ nick:marcan
#asahi-dev · 2021-01-30 15:07
marcanI'll leave this pulling crash/nocrash bits overnight
#asahi-dev · 2021-01-30 15:07
marcananyway, going to call it a day
#asahi-dev · 2021-01-30 15:06
marcankettenis: yeah, figured that would work (or I can just make m1n1 lie about it)
#asahi-dev · 2021-01-30 15:05
marcanbut they suck in many ways
#asahi-dev · 2021-01-30 15:05
marcanthough they will *probably* work for this
#asahi-dev · 2021-01-30 15:05
marcanalso, I would avoid "bidirectional" level translators
#asahi-dev · 2021-01-30 15:05
marcanyes, you can't use resistor dividers for power supplies unless you use really low value resistors :p
#asahi-dev · 2021-01-30 14:56
marcanBluerise: that looks like it should work
#asahi-dev · 2021-01-30 14:54
marcanis it hard to just make it support x2r10g10b10?
#asahi-dev · 2021-01-30 14:54
marcanI mean, we could do that if we needed to
#asahi-dev · 2021-01-30 14:54
marcankettenis: I saw corellium were patching that in the display controller
#asahi-dev · 2021-01-30 14:49
marcanwell, you need a 1.8V supply for the muart, right? :p
#asahi-dev · 2021-01-30 14:46
marcanBluerise: a 220 ohm + 470 ohm divider will give you ~1.2V out of a 1.8V signal
#asahi-dev · 2021-01-30 14:46
marcanthen I guess all you need is some 1.8V reference voltage from somewhere
#asahi-dev · 2021-01-30 14:45
marcanBluerise: cool :)
#asahi-dev · 2021-01-30 14:36
marcanI have it running in a loop incrementing base addresses by 64K, I'll leave it overnight and see if I see patterns tomorrow :)
#asahi-dev · 2021-01-30 14:34
marcanarnd: 16K right now (in m1n1)
#asahi-dev · 2021-01-30 14:30
marcanthat part is critical
#asahi-dev · 2021-01-30 14:30
marcanwith SOP'DEBUG
#asahi-dev · 2021-01-30 14:29
marcan1.8V converters are fine (3.3V won't work, threshold is too high) if you do that
#asahi-dev · 2021-01-30 14:29
marcanso you would need to run it at 1.8V and use a resistor divider on the TX direction
#asahi-dev · 2021-01-30 14:29
marcanthat UART you linked does down to 1.8V
#asahi-dev · 2021-01-30 14:29
marcanbut yeah, if you can do compliant DFP negotiation and send SOP'DEBUG/SOP''DEBUG VDMs it should work
#asahi-dev · 2021-01-30 14:28
marcanpretty sure it should be possible with a standard type C cable
#asahi-dev · 2021-01-30 14:28
marcanactually one thing I need to try out, if I find some time tomorrow, is to make this work with a simple M1 - M1
#asahi-dev · 2021-01-30 14:28
marcanalso you need to be a DFP
#asahi-dev · 2021-01-30 14:27
marcanincluding sending SOP'DEBUG VDMs?
#asahi-dev · 2021-01-30 14:27
marcanBluerise: do you have the USB-PD stuff?
#asahi-dev · 2021-01-30 14:26
marcanglasgow in 1.65V mode and a resistor divider for the TX side
#asahi-dev · 2021-01-30 14:25
marcanthat screams like a cache/TLB problem to me
#asahi-dev · 2021-01-30 14:25
marcanand whether it happens depends on the load address of m1n1
#asahi-dev · 2021-01-30 14:25
marcanit's a fun one: leaving that register enabled, I get SError faults (after a few times, an endless loop) after normal page faults - but not always
#asahi-dev · 2021-01-30 14:24
marcanI'll test it as soon as I'm done with the current oddysey
#asahi-dev · 2021-01-30 07:33
marcancorellium sets that one to zero, disabling all faults, thus shoving all address issues under the carpet :)
#asahi-dev · 2021-01-30 07:33
marcandocumenting another mystery register: https://github.com/AsahiLinux/docs/wiki/HW:ARM-System-Registers#sys_l2c_err_sts
#asahi-dev · 2021-01-29 18:18
marcangood night ;)
#asahi-dev · 2021-01-29 18:18
marcantomorrow smp bringup
#asahi-dev · 2021-01-29 18:17
marcanpassing the basic memory/fb info from adt to fdt
#asahi-dev · 2021-01-29 18:17
marcanit can boot linux properly now
#asahi-dev · 2021-01-29 18:16
marcan(see the commit)
#asahi-dev · 2021-01-29 18:16
marcanmight as well, you know, use them
#asahi-dev · 2021-01-29 18:15
marcanand it's not about checking, we have the lengths, and I had just added some fancy foreach macros that *do* in facto do it all properly
#asahi-dev · 2021-01-29 18:15
marcanmodwizcode: fixed
#asahi-dev · 2021-01-29 18:11
marcanoh yeah that's buggy heh
#asahi-dev · 2021-01-29 18:09
marcanthe thing is passing around the size to everything is a PITA
#asahi-dev · 2021-01-29 18:09
marcanwonder if there's a terminator guaranteed
#asahi-dev · 2021-01-29 18:09
marcanyeah it doesn't use the size right now
#asahi-dev · 2021-01-29 18:08
marcanI don't hardcode addresses any more except for UART and AIC right now
#asahi-dev · 2021-01-29 18:08
marcanas of a few commits back it's required
#asahi-dev · 2021-01-29 18:08
marcanoh, well, um, yes, it does kind of expect to have a real devicetree

plus ›