#
…

2021-06-25

01:00DragoonAethis has quit [Quit: hej-hej!]
01:00DragoonAethis has joined #asahi
02:57bgbabout vmdtool: stuck at Poll: cc1=1 cc2=1, what's going on? https://paste.debian.net/1202301
03:03phiologe has joined #asahi
03:06PhilippvK has quit [Ping timeout: 480 seconds]
03:18aquijoule_ has joined #asahi
03:24aquijoule__ has quit [Ping timeout: 480 seconds]
03:35marvin24 has joined #asahi
03:38marvin24_ has quit [Ping timeout: 480 seconds]
05:46tertu has quit [Ping timeout: 480 seconds]
06:17marcanbgb: are you using a cable, or using a connector directly on the mac?
06:17marcanif the latter, did you connect both CC lines? if so, that's wrong, connect only one
07:09bgbmarcan: I'm using a cable, I think maybe I miss pull-up/pull-down of cc pins
07:22Namidairo has quit [Remote host closed the connection]
07:22Namidairo has joined #asahi
08:01marcanbgb: the pulls are internal
08:01marcanbgb: are you using a 5V arduino and did you wire VBUS properly?
08:03bgbmarcan: arduino UNO, VBUS connected with Arduino D4
08:05bgbmarcan: you mean fusb302 pulls cc pins internally
08:10marcanbgb: yes
08:12marcanbgb: you're using a male-male type C cable?
08:13marcancc1=1 cc2=1 is usually a sign that both CC pins are connected through, which means no standard cable in use and both pins incorrectly connected through to the mac
08:14marcaneither that or there's a short somewhere and both pins are connected together for some reason
08:16tsida has joined #asahi
08:18bgbmarcan: I made a fusb302 breakout board with connector(female), cc1 and cc2 connected, the board and mini are connected via thunderbolt cable
08:24marcanbgb: measure the voltage on both CCx pins with a multimeter
08:28bgbmarcan: there isn't a multimeter around, I'll check later
08:35marcanyou might also want to try a non-thunderbolt cable
08:36marcanI'm not sure if anyone has ever tried an active cable like that
08:36marcanin theory it should work, but you know
08:38sveni just love how anything usb just gets more and more cursed with each revision :/
08:38bgbbtw, I soldered the little fusb302 manually, and maybe already broken
08:53marcanyou might also just have a short between the CCx pins :-)
08:57bgb has quit [Ping timeout: 480 seconds]
09:09bgb has joined #asahi
10:29bgb_ has joined #asahi
10:29bgb_ has quit []
10:37bgb has quit [Ping timeout: 480 seconds]
11:04bgb has joined #asahi
11:12bgb has quit [Ping timeout: 480 seconds]
11:21bgb has joined #asahi
11:29bgb has quit [Ping timeout: 480 seconds]
11:39bgb has joined #asahi
11:48bgb has quit [Ping timeout: 480 seconds]
11:56bgb has joined #asahi
12:17bgb has quit [Ping timeout: 480 seconds]
12:24yuyichao has quit [Quit: Konversation terminated!]
12:24bgb has joined #asahi
12:24yuyichao has joined #asahi
12:31aleasto has joined #asahi
12:48aleasto has quit [Ping timeout: 480 seconds]
13:55bgb_ has joined #asahi
14:00bgb_marcan: cc not short; before plug cc1 = cc2 = 3.3V ; after plug cc1 = 0.08v cc2 = 0.06v
15:13bgb_ has quit [Ping timeout: 480 seconds]
15:37marcanbgb: those numbers are too low. 0.06 is nominal for vconn, but 0.08 is way too low for CC
15:38marcanit should be more like 1V
15:38marcanor at least >0.2V or so
15:38marcanthe code configures the threshold at 0.2V
15:39marcanthe spec says 0.25V - 1.60V is the valid range for vRd (CC line)
15:39marcantry a different cable? maybe something is strange...
15:41marcanalso try flipping the cable on the FUSB side. the voltage should at least swap cleanly, if they don't then something is weird/asymmetric in your board/FUSB
17:11skipwich has quit [Quit: DISCONNECT]
17:32aleasto has joined #asahi
17:38jbowen_ has quit [Quit: leaving]
19:12skipwich has joined #asahi
19:34aleasto has quit [Remote host closed the connection]
19:58PhilippvK has joined #asahi
20:01phiologe has quit [Ping timeout: 480 seconds]
20:36aquijoule_ has quit [Remote host closed the connection]
20:37richbridger has joined #asahi
21:22tertu has joined #asahi
21:27choozy has joined #asahi
22:31tertu has quit [Ping timeout: 480 seconds]
…